Chevrolet Silverado GMT800 3D-printed parts
70 free models that name the Chevrolet Silverado GMT800 (1999–2006), by its generation or its years. Parts that just say Silverado are on every Silverado part.
Add a part
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your rig, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Chevrolet Silverado GMT800 parts
70 parts-
Door armrest switch panel clipGMT800 Silverado, Sierra, Tahoe, Suburban and Yukon, 1999 to 2007. Front door armrest, where the switch panel clips inABS or PETG, solid, upside down with supports. Scuff and epoxy it in. -
Armrest switch panel clipGMT800 trucks and SUVs 1999–2007, driver and passenger -
Radio knobGM trucks and vans 1995–2005, Delco volume and tuner knobs -
Radio knob2002 Silverado 2500HD -
Wideband gauge mountSierra and Silverado 1999–2006, under the vent pocket -
Dash pocketGMT800 Chevy trucks 1999–2006 -
A-pillar trim clip repairGMT800 Silverado 1999–2007, front pillar covers -
Rear window latch linkExtended cab Silverado and Sierra, 1999 to 2007, rear swing-out window. Fixes wind noiseASA or PETG, upright as installed with supports. Several lengths included. -
Cup holder insertGMT800 Tahoe, Suburban and Silverado 1999–2006 -
52 mm vent gauge podChevy trucks 1999–2007, mounts a gauge in the dash vent -
Door switch post repairGMT800 Silverado, Tahoe, Suburban and Yukon 1999–2007 LT, front post fix -
Bed post hole coverSilverado 1500, made for a 2004, likely fits other years -
Cup holder1999 Silverado and Suburban, K1500 and K2500 -
Cupholder insertSilverado 1999-2002, cupholder insert -
Tailgate rod clip, left and right2004 Silverado 1500, holds the tailgate latch rods -
Auxbeam ceiling mount adapterSilverado and Chevy trucks 1999–2007, mounts Auxbeam gear to the ceiling -
Front cup holder insertSilverado 2001–2006, front cup holder -
Stake pocket capSilverado 2002, bed rail stake pocket cap -
Rear speaker adaptersSilverado 1999-2006, rear speaker adapters -
CTS3 overhead mountSilverado 2002, overhead mount for a CTS3 controller -
Fuel door bumperSilverado 1996-2006, fuel door bumper -
Center console radio deleteGMT800 1999-2002 center console -
Split 4x6 speaker adapter bracketSilverado and GMC Sierra GMT800, split 4x6 speaker adapter bracket -
ATOTO USB mountSilverado, Tahoe, Suburban and Yukon GMT800 LT 1999-2007, USB port mount for an ATOTO head unit -
Magnetic wireless charging phone mountSilverado 1999-2006, magnetic wireless charging phone mount -
Edge CTS3 mount1999–2006 Chevy and GMC trucks, mount for the Edge CTS3 monitor -
Gauge cubby cover plateGMT800 trucks, cubby cover plate for an AEM 30-0300 gauge -
Door control panel clip2003–2007 Silverado -
8HP shifter console insertGMT800 2003-2006 trucks and SUVs swapped to the 8HP, OE-style shifter surround -
Seat recline handle1995–2001 C/K1500 and other GM trucks -
Tailgate handle coverChevrolet Silverado 1999 (GMT800, 1999–2006) -
Air box intake grommetSilverado 1994-2017, air box intake grommet -
Tailgate side bumper pads1999–2006 Chevy and GMC pickups, anti-rattle pads for the tailgate sides -
ClipSilverado 2000, retaining clip -
Power window switch rocker2003–2006 Chevy and GMC trucks and SUVs, replacement window switch rocker -
Coolant restrictorSilverado 2001, 0.10 inch coolant restrictor -
Door latchSilverado 1999–2004, replacement for the latch that holds the front and rear doors fully closed -
60mm gauge panel2000-2006 Tahoe and Chevy 1500, panel for 60mm gauges -
Daylight sensor coverSilverado GMT800, dash daylight sensor cover -
Upper cubby insert for an 8HP swapGMT800 2003-2006, mounts a TurboLamik screen and selector knob in the upper console cubby -
Arm rest switch panel supportGMT800 trucks and SUVs 1999-2007, reinforced arm rest switch panel -
Jump seat cup holder bracket, GMT800 to GMT900GMT900 Silverado center jump seat, mounts the GMT800 jump seat cup holders using the existing bolt holes -
A/C controls blank1999–2006 GMT800 trucks, blank for the A/C control opening, plus a three gauge pod version -
-
Door lock part1999 Silverado, replacement piece for the door lock -
Edge CTS3 monitor mountSilverado 1999–2006, holds an Edge CTS 3 or CTS 2 in the cubby by the 4WD switch -
Dash cubby ball mountAvalanche GMT800 dash cubby, 17mm ball mount for a MagSafe charger -
A-pillar trim clip repairGMT800 GM trucks. Glues over a broken A-pillar trim clipPETG at 0.16 mm. Cut the broken clip flat first; super glue it on. -
Cup holder clip2002 Silverado 1500HD similar to 88934982 -
Interior trim pieceSilverado 2000 and Tahoe, interior trim piece -
Rear window latchSilverado 1999–2003, fixes rear window wind noise -
Radio tuner knob2001 Silverado, replacement radio tuning knob -
Cassette pocket2002 Silverado, storage pocket for the cassette slot -
Center console rear cubbySilverado 2001-2006, rear cubby for the center console -
CB radio dash bezelSilverado 2001-2006, dash bezel for a CB radio -
Phone holder2005 Silverado, phone holder -
Overhead console gauge pod2003 Silverado 1500, gauge pod in the overhead console -
4-cup holder2006 Silverado, four cup holder -
Front cup holder insertSilverado 2001-2006, front cup holder insert -
60mm gauge panelTahoe and Silverado 1500 2000-2006, 60mm gauge panel -
Rear monitor mountGMT800 Silverado, Tahoe, Suburban and Avalanche 2002-2006, rear monitor mount -
Tailgate bump stopSilverado and GMC Sierra 1999-2007, tailgate bump stop -
Lighter socket phone mount receiverAvalanche, Silverado, Suburban and Tahoe 2003-2006, phone mount in the lighter socket -
YETI mug cup holder adapterSilverado, Tahoe and Suburban 1999-2014, holds a YETI 14 oz mug -
Console cup holder1995–2000 Silverado, Tahoe and Suburban, drops in where the console CD holder was -
Four toggle switch panel1995–2000 Silverado, Tahoe and Suburban (OBS), drops into the center console CD holder -
Cup holder tab, longerGMT800 Silverado, longer and thicker cup holder tab that grips 12 oz cans -
Spare tire crank tube and plug2004 Avalanche, replaces the rear bumper tube, cover and keyed plug; unscrews with the tire iron. Likely fits other GMT800 trucksPETG, ASA or ABS, no supports. -
Ashtray cup holder insert2004 Avalanche, drops into the console where the ashtray lifts outTPU, no supports. -
Rear lower body mount2004 Avalanche, the mount under the rear of the box; likely other GMT800 trucksTPU 95A.
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Chevrolet Silverado GMT800 parts free?
Yes. All 70 are free to download from the creator's page. 42 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Chevrolet Silverado GMT800?
Check the years and trim in what each part fits, match the OEM part number where it's listed (1 of the 70 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Send us one
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
Got it
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.