Ford clips, knobs and trim
35 free models for the F-Series, Ranger, Bronco, Explorer and Expedition. Ford trucks and SUVs, from OBS F-Series and Broncos to the Lightning.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Ford
Ford parts
35 parts-
Fuel line retainer clip2015 Ford Ranger, retaining clip for the fuel line at the fuel filter endPrint with 0.6mm line width. -
Center console bumper2021–2025 F-150 -
Frunk trim clipFord F-150 Lightning, trim clip for the front trunk (larger size)Print in ABS/ASA or something with similar or better heat resistance. -
Floor mat retaining clipsFord carpet mats (made for a Transit Custom) -
Seat adjustment handleFord seat recline handle -
Door and tailgate latch rod clipFord trucks and other Ford/GM vehicles, retainer clip on door and tailgate latch rods F65Z-1521952-AA, F7DZ-7421952-AACreator switched to PC Blend for strength; PLA only for test fits. -
Tie-down hook coverRanger bed tie-down hooks -
Center console armrest latch2012-on Ranger -
Tailgate pivot bushingsFord F-150 tailgate hinge/pivot bushings; should fit what the Dorman 38641 kit fitsPrint in PETG, ABS or nylon with supports and 50%+ infill; PLA is too brittle. -
Fuel line clipsRanger and Mazda BT-50 -
Shifter detent plunger2009-2017 Ford F-150, Expedition and Lincoln Navigator, small detent part inside the floor shifter FL1Z-7210-BAPrint in ABS or similar heat-tolerant material. -
-
Firewall A/C line clip1992-1997 OBS Ford F-Series trucks, clip on the firewall that holds the A/C linePrint in CF nylon or another high-temperature material; no supports, brim may help. -
-
Hood bumper1992-1996 Ford Bronco, F-150, F-250, F-350 (OBS), rubber hood stopTPU with 4 walls and about 20% cubic infill. -
Hood prop rod clipFord Ranger (possibly other Fords), clip that holds the hood support rod when stowedPrinted in PETG with supports. -
Sun visor clip2005 Ford F-350 Super Duty, headliner clip that holds the sun visor -
Tailgate cushion retainer rivetFord F-150, rivet that holds the rubber tailgate bumper/cushion to the bedPrint the female part in TPU with no supports inside it; male part can be PETG. -
-
Hood prop rod clipRanger and Everest -
-
Mountain Top cover lever clipRanger with a Mountain Top roller cover -
Defroster connector cover2021+ Ford Bronco and Bronco Sport, covers for the rear window defroster wire connectorsNo supports; PETG recommended; print both mirrored parts. -
Jack cover quarter-turn knob2000-2005 Ford Excursion, quarter-turn retainers for the rear jack coverPrint at 45 degrees with snug supports, 3 walls; PETG-CF, ASA or ABS. -
Tailgate clipGen 3 Ranger -
Bed divider clipRanger bed divider -
Heater vent clipsRanger Raptor T9 -
Fender liner retainerFord F-150, Explorer and other Fords, push-type fender retainersPrinted with a 0.6mm nozzle in PETG-HF. -
Console cubby cover2021-on F-150, in front of the shifter -
Sunroof glass clips1991-1994 Ford Explorer, clips that hold the sunroof glassPLA will melt; creator recommends PPS-CF. Reuse the original screws and springs. -
Ignition bezel2019 Ranger -
Rear soft top bracketBronco -
Fuse panel twist lock fastener1999–2002 F-Series, trim panel under the steering wheel -
Door lock knobFord F-150 and many Ford trucks 1991-2014 (creator's estimate), interior door lock post knob FODZ-5421850-APrinted in PETG for heat; ASA, PA or ABS also suggested. 0.08mm layers, 3 walls, 100% infill. -
Coin tray stopper2018 F-150
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Ford parts free?
Yes. All 35 are free to download from the creator's page. 25 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Ford?
Match the OEM part number where it's listed (4 of the 35 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
20 from MakerWorld, 14 from Printables and 1 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.