Toyota clips, knobs and trim
53 free models for the 4Runner, Tacoma, FJ Cruiser, Tundra, Land Cruiser, and Hilux and pickup. Most Toyota trim clips share a handful of part numbers across trucks, so look for yours in the 90467 series on the old clip or in the parts catalog.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Toyota
Toyota parts
53 partsBefore you print, find out what the clip actually is. FJ Cruiser Forum member 101Firedog keeps a visual encyclopedia of FJ Cruiser fasteners, with photos and the Toyota part number for each trim clip.
-
Radio and center console clip4Runner, FJ Cruiser, Tacoma, Tundra, Sequoia, Land Cruiser. Check the years on the page. 90467-10203PLA at 100% infill in the creator's profile; PETG lasts longer in a hot cab. -
Grille clipTacoma 1995–2004, 4Runner 1989–2002, grille to framePETG on its side. Turn on detect thin walls. -
Air dam control arm plugs2024-on Tacoma with the front air dam removed; stops the whistle -
Trim clipMany Toyotas. Used on a 2007 Tundra, fender liner to bumperNylon. PETG split in one orientation. -
Interior panel clipTacoma, door panel behind the mirror 90467-09204 -
Toyota/Lexus plastic clipMost 2000-on Toyota and Lexus 90467-07220Print on its side with supports. -
Door clip repair tab80-series Land Cruiser. Glue it to a torn panel so new clips can gripPLA and super glue. -
Rear vent air redirector5th gen 4Runner and Lexus GX460, rear seat vents -
-
Cup holder module4Runner center console, the slot next to the cup holder -
Grille lock clipHilux and Corolla, 1979–1983 -
-
-
Sharkfin antenna delete cover2015 5th gen 4Runner, lets a rooftop tent sit lower -
Fender clip1995 Tacoma 4WD fender -
ECM cover2022-on Tundra and Sequoia -
-
Taillight body clip1st-gen Tacoma -
Lower center console covers1996–2004 Tacoma -
Hidden compartment cover clips4Runner rear cargo compartment cover -
Roof rail spacers4th gen 4Runner rain rail, under a roof rackButyl tape underneath to seal out water. -
-
Rear panel hook extension2023 Tacoma rear cab panel hook -
Visor clip blank80 Series Land Cruiser, after replacing the stock visorsNot PLA; it deformed in the heat. -
Yellow dash clip2007 Tundra dash clip, the yellow one Toyota uses all over the dash 90467-10203ABS.
-
Windshield wiper bolt coverFJ Cruiser
-
Under-hood fuse box clipTacoma fuse and relay box cover latchPETG, ABS or nylon. Grind off the old clip; a little glue helps.
-
Grille clip1st-gen 4Runner, 1987, grille to body
-
Headlight filler panel clip3rd-gen 4Runner. Passenger side; mirror it for the driver sideNot a copy of the factory clip: uses double-sided tape.
-
Fender moulding clipLand Cruiser Prado wheel archPrint as uploaded, support on the build plate only.
-
Rear step cover nut80-series Land Cruiser, 1990–1997 90467-04020Drill out the pilot hole to your screw. Print extras.
-
Hood prop rod clipFJ60 Land Cruiser. The STL is attached to the forum post100% infill; the post shows the strongest orientations.
-
Heater hose separatorFJ40 Land Cruiser, two lines
-
Early wiper coverFJ40 Land Cruiser
-
Center console box lock80-series Land Cruiser, the box between the seats
-
Lower tailgate release lever80-series Land Cruiser
-
Bumper clipToyota bumper clip; the creator calls it a work in progress 90467-05081
-
Climate control knobsFJ Cruiser, remixed
-
Hood vent trim, all threeFJ Cruiser hood ventsABS or another heat-resistant filament; PLA bends in the sun.
-
Snorkel grilleFJ Cruiser snorkel head, made after a bird broke one on a 2011
-
Power outlet coverFJ Cruiser
-
Center console coverFJ Cruiser center console
-
Cup holder linerFJ Cruiser
-
Cup linerFJ Cruiser
-
Grab handle mountFJ Cruiser grab handle, adds a mount without losing the handle
-
Defrost knob1970s FJ40 heater, bolts on with an M3 screw
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Toyota parts free?
Yes. All 53 are free to download from the creator's page. 26 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Toyota?
Match the OEM part number where it's listed (7 of the 53 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
28 from Thingiverse, 12 from MakerWorld, 12 from Printables and 1 from a forum thread. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.