GMC clips, knobs and trim
33 free models for the Sierra, Canyon, Yukon and Jimmy. The Envoy is filed under Yukon and the old C15 under Sierra. Most GM clips carry over from the Chevy twins, so check the Chevrolet page too.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
GMC
GMC parts
33 parts-
-
Washer fluid reservoir cap2014 GMC Sierra, windshield washer fluid reservoirPrint in TPU for flexibility. -
-
Gear shift pointer indicatorChevy and GMC trucks with the GM column shift pointer 7840995PETG or ABS; PLA can warp from cabin heat. -
Rear door latch handle1999-2007 Sierra extended cab, rear-hinged rear door latch handleABS or ASA, no supports needed. -
Capless fuel filler cover2023+ Canyon, capless fuel filler (66 mm ID) with door-mounted holderPrint in TPU. -
Bed rail stake pocket cover2019-2025 Sierra and 2023-2026 Canyon bed rail stake pocketsPrint in ASA for UV and heat resistance. -
Parking sensor retainer2015 GMC Sierra rear bumper parking sensor; other models using OEM 23276807 23276807Print in PETG; scale so the x/y size is 30.4 mm. -
DSSV frame tube plug2023+ Canyon AT4X with DSSV shocks, passenger side frame mount tubeTPU at 100% infill. -
Bed stake pocket cover, with tabsSierra AT4 -
Capless fuel filler cover2018 Sierra 1500, capless fuel filler (60 mm ID)TPU, 3 perimeters, 5 top and bottom layers. -
Blend door actuator gear1990s-2000s S-15 Jimmy and other GM vehicles, HVAC blend door actuatorPrinted in PA6-CF. -
Sun visor mirror cover2018 Yukon Denali, passenger sun visor vanity mirror coverABS or ASA, printed at 45 degrees with tree supports. -
Rear cargo cover pull handle1995-2005 S-15 Jimmy, rear cargo cover pull handleABS or ABS-GF, print vertically with a raft; avoid PLA. -
-
Soft tonneau cover clipGMC Sierra EV with soft tonneau cover, holds the cover in the front rail channelPETG, 40% infill, 3 walls; screws in with #8 flat head screws. -
Grab bar screw coverYukon, plus Tahoe and Silverado -
Center console cover2014–2018 Sierra -
Seat tilt button2007 GMC Canyon, press-fit replacement for a broken seat tilt buttonABS in hot climates, 50% infill, no supports. -
-
Headlight retaining clipGMC and Chevy trucks
-
Tonneau support rod clip2015–2025 Canyon factory hard tonneau cover
-
Stereo EQ knob2000 Sierra SLE
-
Tailgate trim clip1973–1987 C15 (Chevy C10 too)
-
Cab molding clip1973–1987 C15 (Chevy C10 too)
-
Rear window switch case2001–2006 Yukon 800755
-
Cruise control clip2000 Jimmy
-
Front seat recline handleJimmy, Sonoma, Canyon and Envoy, plus Chevy S10 and Blazer
-
A/C knob2004–2012 Canyon (Chevy Colorado too)
-
Door panel anchors2007 Envoy
-
Center console latch2002 Envoy, may fit later Envoys
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these GMC parts free?
Yes. All 33 are free to download from the creator's page. 17 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my GMC?
Match the OEM part number where it's listed (3 of the 33 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
14 from Printables, 13 from Thingiverse and 6 from MakerWorld. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.