Nissan clips, knobs and trim
21 free models for the Patrol, Frontier, Titan, Xterra and Pathfinder. The Frontier chip covers the Hardbody and Navara, and the push pins and hood prop clips Nissan shares across its trucks are in here too.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Nissan
Nissan parts
21 parts-
Push pin retainerCommon Nissan/Infiniti push rivet, 8mm hole, under-hood cowl and trim panels 01553-09321 (superseded by 01553-2DR9A)Nylon preferred, PETG works; use the solid-tab retainer. 20mm and 16mm flange versions -
Wiper cowl top grilleWD21 platform Pathfinder, Hardbody and Navara cowl panels below the windshield, left and right 66820-01G00 / 66821-01G00Designed for bolts instead of clips; mirror for the other side; large print -
-
Washer reservoir cap2001 Xterra windshield washer fluid reservoir -
Exterior trim clip2013 Frontier exterior trim; likely fits other Nissans of similar ageTPU at 0.32mm layers -
Hood prop clip1987 D21 Hardbody hood prop rod retainer; may fit later yearsNylon (CoPA), anneal; tree supports from build plate; 0.2mm nozzle used -
Sunroof cover clipD21 Hardbody pop-up sunroof cover latch clipABS or similar for cab heat; coin slot down, supports for the cams -
-
Center console latch clipNavara D22 (confirmed 2011 YD25, likely 2008-2015) center console lid latchReinforced over the OEM clip -
Body clipsNissan bodywork, direct fit or with a wider lip -
Shift knobPatrol Y61 (GU) and Y60 (GQ) manual gear stick, 10x1.25mm threadPrint upside down; 5 perimeters, 25% infill; use V2 (deeper thread) -
Brake booster hose clipFrontier and Xterra, clip holding the brake booster hose to the firewallPETG -
Seat recline switch knob1st gen Titan 2004-2015 power seat recline switch; also 1st gen Armada and QX56 87013-7S001Two versions: chamfer only (easier) or chamfer plus fillet -
Hood prop rod clipNissan hood support rod clip for 8mm rod; creator lists Pathfinder, Navara, D21, Sentra, Altima, Maxima, Z cars 65722-01E00 / 65722-65F00ABS, 0.16mm layers, 4 walls -
Fender flare repair pin2013 Titan Pro-4X OEM fender flares, replaces broken molded-on pins; may fit earlier yearsPLA or PETG, 0.2mm, 4 walls, 100% infill, tree supports -
Roof rail gutter capsPatrol Y62 Ti-L roof railing gutter end capsASA or PETG; PLA will deform on a hot roof -
Shifter cable bushingAutomatic shifter cable bushing: Frontier 2005-2021, Titan 2005-2021, Xterra 2005-2015, Pathfinder 2005-2012, Armada 2004-2015 34935ZR00A / 349357S00TPU only; creator calls it a temporary fix -
Indicator repeater clipGU Patrol
-
Hood prop rod clipNissan
-
Hood prop rod clipNissan
-
Center console switch blankHardbody D21 pickup through 1997
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Nissan parts free?
Yes. All 21 are free to download from the creator's page. 7 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Nissan?
Match the OEM part number where it's listed (5 of the 21 have one), or pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
11 from Printables, 6 from MakerWorld and 4 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.