Ram and Dodge clips, knobs and trim
30 free models for the Ram 1500, Ram 2500 and 3500, and Dakota. Dodge Rams from the 2nd gen on and the Ram trucks after them. The 2500 parts generally fit the Power Wagon.
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Most downloaded
Ram and Dodge
Ram and Dodge parts
30 parts-
Tow hook cover2021-on Ram 1500 -
Cup holder adapter4th gen Ram 1500 and Classic -
Rear cup holder cover4th gen Ram 1500 crew cab, rear floor cup holder cover -
Bed stake pocket cap2003 Dodge Ram 1500, bed rail stake pocket plug -
Seat recline lever1994-2002 2nd gen Dodge Ram, driver seat recline lever (16-groove 12 mm shaft)Print the fit test first. PETG, 6 perimeters, spud side up, no supports; ASA or nylon for durability. -
Passenger door cup holder2019–2025 Ram 1500 -
Stereo bezel and brackets2006–2009 Dodge Ram -
Bed stake pocket cover2019–2025 Ram 2500 -
Headlight back cover2014 Ram 1500, headlight bulb dust cover (stock and LED-clearance versions)Mirror the file for the other side. -
Fuse box cover2011 Ram 1500 (4th gen) -
Windshield trim push nut1994-2002 2nd gen Dodge Ram and other Dodges, windshield trim fastenerPrint head-down without supports in PETG; glass-filled ASA or nylon is better. Use plenty of perimeters. -
Antenna base and gasket2009-2018 Ram 1500, replacement roof antenna baseBase in ASA for UV, gasket in TPU. -
A-pillar trim repair2005 3rd gen Dodge Ram, fix for the A-pillar trim mountPETG-CF, 20% infill. Tight fit, no glue needed. -
Cup holder adjuster1994-2002 2nd gen Dodge Ram 2500, replaces the toothed cup holder adjuster -
Bed wiring grommet2023 Ram 2500, snap-in bed plug grommet for 3/8 in loom -
Upper radiator hose support clip2009-2018 Ram 1500 5.7L, upper radiator hose support (only sold with a new hose)ABS or ASA for hose heat; integral supports, no extra supports needed. -
Glovebox hinge bracket2001-2002 Dodge Ram 2500, replaces broken glovebox hinge points100% infill. Reuses two original screws. -
A/C temperature slider knob1st gen Dodge Ram D250 Cummins (about 1990), HVAC temperature slider knobPETG at 0.10 mm layers. -
Door handle screw cover1997-2004 Dodge Dakota, cover for the screw behind the inner door handle0.2 mm layers, 100% infill. Tight fit. -
Floor mat clip2018 Ram 1500 front mats -
Jack anti-rattle spacer4th gen Ram 1500 -
Side console bolt cap2022 Ram 2500, likely other 5th gens -
Center console mount repair1997-2004 2nd gen Dodge Dakota, repairs broken console screw mountsDrill out the old mounts first; glue in if needed. -
-
Door lock plunger1990s Dodge Dakota Sport, interior door lock knobUse the included 3MF with bottom supports and brim; 0.15 mm layers. -
Rear window regulator cable guide2009–2019 Ram 1500 and 2019–2020 Classic -
Cab plug2024 Ram 2500 -
Push pin retainer clipRam trucks, general Mopar-style push pin for 6.3 to 6.5 mm holesPETG, ABS or nylon; 0.16 mm layers, 2 walls, 15% infill. -
Lower dash switch panel2006–2009 Ram 2500 and 3500, below the lighters
-
Bed stake pocket plugs2019-on Ram HD
Nothing for this model yet. Send us one.
Any make
2 partsClips that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011
-
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Ram and Dodge parts free?
Yes. All 30 are free to download from the creator's page. 20 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right clip for my Ram and Dodge?
Pull the old clip and compare it with the preview photos and what each part fits.
What filament should I print trim clips in?
PETG, ASA or nylon. PLA goes soft in a hot cab, so save it for a test fit. Print one, check it against the old clip, then print the rest.
Where do the files come from?
15 from Printables, 13 from MakerWorld and 2 from Thingiverse. LRDT doesn't host the files; every part links to its creator's page.
Can I add a part?
Yes. Send the link with the form at the bottom of this page. We check the fit and the license, then add it with the creator's name on it.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.