Chevrolet TrailBlazer parts
18 free models made for the Chevrolet TrailBlazer, plus 18 that fit every Chevrolet. Looking for another Chevrolet? See every Chevrolet part.
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Chevrolet TrailBlazer parts
18 parts-
Double DIN dash kitTrailBlazer 2002–2009, double DIN head unit install -
6.5 inch front door speaker adapterTrailBlazer 2002–2009, Bose door locations to aftermarket 6.5 inch speakers -
Dash speaker to tweeter adapterTrailBlazer, adapts the dash speaker opening to a tweeter -
Sun visor glasses clipChevy TrailBlazer, clips that hold glasses on the sun visor -
Bump stopTrailBlazer, replacement bump stop -
-
Ignition coil sealTrailBlazer and Envoy 2002-2009 4.2L I6, ignition coil seal -
Cup holder adapterTrailBlazer, cup holder adapter with TPU tabs -
UHF mount switch spacerHolden Colorado and Trailblazer, UHF radio mount with switch spacer for XRS and GME -
Transmission cable mountTrailBlazer, transmission cable mount -
Window regulator slide bracketChevrolet TrailBlazer (generation not stated) -
Window slide bracketTrailBlazer, window slide bracket and guide -
Rear window switch bezel2005 TrailBlazer, rear window switch -
Captains chair controller clipsTrailBlazer, clips for the captains chair controls -
Fuel door springTrailBlazer and GMC Envoy, fuel door spring -
Engine cover mounting bracketTrailBlazer SS, engine cover bracket -
Shift knobTrailBlazer, shift knob -
Power seat track shimTrailBlazer and GMC Envoy, power seat track guide bushing
Fits every Chevrolet
18 partsParts made for Chevrolet trucks in general. Check the fit on yours before you print.
-
Map pocket cup holder1977–1991 squarebody Chevy trucks, door map pocket -
Airbag switch delete plateS-10, Sonoma and Hombre 1998+, blanks off the passenger airbag switch -
Center consoleChevrolet -
Center console cup holderChevy trucks (1998), center console -
Ash tray USB and aux adapterSquare body K5 Blazer, replaces the ash tray with USB and aux ports -
Climate control knobS-10 1994–2004, replacement climate control knob -
Single DIN dash plate1st gen S-10 and S-10 Blazer, single DIN radio mount -
Cup holdersS-10 Blazer, 1st and 2nd gen -
Window switch repair partChevy and GMC trucks 2003–2006, window switch repair -
Lug nut coversS-10 -
Tail light junction block mountChevy short bed pickups, mounts the tail light junction block -
Headlight clipS10 and GMC Sonoma 1994–2004, may fit the S15 Jimmy -
Bench seat cup holderS10 1995, bench seat cup holder sized for Contigo-style mugs -
Radiator cap removal toolGMC and Chevy; grips a stubborn radiator cap without pliers -
HVAC knobS10 and Blazer 1994–1997, temp and mode knob for the HVAC panel -
Radio tuner knobChevy S10, replacement radio tuner knob -
Window rollerChevy S10, replaces a broken window roller mechanism -
Parking brake lever1994–2004 S-10, Sonoma and Blazer 4WD, rear parking brake lever (discontinued by GM)
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Chevrolet TrailBlazer parts free?
Yes. All 36 are free to download from the creator's page. 25 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Chevrolet TrailBlazer?
Check the years and trim in what each part fits, match the OEM part number where it's listed (0 of the 36 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.