Toyota Tacoma 1st gen 3D-printed parts
66 free models that name the Toyota Tacoma 1st gen (1995–2004), by its generation or its years. Parts that just say Tacoma are on every Tacoma part.
Add a part
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your rig, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Toyota Tacoma 1st gen parts
66 parts-
Dash switch coverOlder Hilux, 1st gen Tacoma, 4Runner and T100, fills switch holes -
Grille clipTacoma 1995–2004, 4Runner 1989–2002, grille to framePETG on its side. Turn on detect thin walls. -
Door handles1st gen Tacoma 1995–2004, replacement handles -
Switch blank lighter holder1st gen Tacoma, 3rd gen 4Runner and others, holds a Bic lighter -
Cup holder insertTacoma 1st gen, cup holder insert -
Dash switch coverGen 1 Hilux, Tacoma, 4Runner and T100, dash switch cover -
Bench seat cup holderTacoma 1st gen, bench seat cup holder -
ScanGauge ashtray mountTacoma 1st gen, mounts a ScanGauge II in the ashtray -
Airbag rocker switch panelTacoma 1st gen, rocker switch panel for the airbag slot -
Dash plugTacoma 1st gen, dash plug -
Dual USB switch mountTacoma 1st gen, dual USB in a switch slot -
Rear window linkageTacoma 2003, rear window linkage -
Clock cubby1st gen Tacoma, replaces a broken clock -
Hood support rod holderTacoma 2000, hood prop rod holder -
Quarter panel vinyl template4Runner and Tacoma 1st gen, template for cutting quarter panel protective vinyl -
Steering wheel radio control mountTacoma 1st gen, mounts an aftermarket steering wheel radio control -
Fender clip1995 Tacoma 4WD fender -
Rear bumper dome caps2nd gen Tacoma 2005–2015 and Tundra 2000–2006, replaces the OEM bumper caps -
Intake plugTacoma 1st gen, intake plug -
Rear sliding window latch catch1st gen Tacoma and T100 -
-
Extended cab window bracketTacoma 1995–2004 extended cab, window bracket -
Ashtray electronics panelTacoma 1st gen, electronics panel for the ashtray spot -
Taillight body clip1st-gen Tacoma -
Coin tray heated seat switch mountTacoma 1st gen, heated seat switch mount in the coin tray -
Radio plugTacoma 1st gen, radio plug -
Dimmer knobToyota truck 2000–2006, dimmer knob -
Lower center console covers1996–2004 Tacoma -
Phone holder adapterTacoma 2003, phone holder adapter -
Washer level float1st gen Tacoma, repairs the washer fluid level sensor -
Grill clips, OE styleToyota Tacoma 1st gen, grill clips 90467-12040 -
Switch blank with USBTacoma 1st gen, switch blank with USB -
Side marker light clips2001–2004 Tacoma 53138-04010 -
Hidden business card holderTacoma 2004, hidden card holder in the glove box -
UltraGauge holder4Runner 3rd gen and Tacoma 1st gen, UltraGauge holder -
Headlight filler panel clip1st gen Tacoma headlight filler panel. Missing on some aftermarket fenders; sticks on with double-sided foam tapeThe creator suggests nylon for heat and UV resistance. -
Fuse panel cover1st gen Tacoma, replacement fuse panel cover -
Passenger side damper controlTacoma 2001 to 2004, passenger side HVAC damper control -
5VZ-FE main seal press tools1st gen Tacoma 3.4 V6 (5VZ-FE), presses in the crankshaft main seals -
Winch control box bracketTacoma 1st gen with ARB bumper, control box bracket for Zeon 8/10/12 winches -
Coin holderTacoma 1st gen, coin holder -
Grill clips, aftermarket styleToyota Tacoma 1st gen, grill clips 90467-12040 -
Door lock motor gearTacoma 1st gen, door lock motor gear -
Dash mountTacoma 1995 to 1996, dash mount -
Fuse cover supports1st gen Tacoma, glue-in tabs that stop the fuse panel cover falling out over bumps -
Ashtray rocker switch conversionTacoma 1st gen, converts the ashtray to rocker switches -
License plate light gasketTacoma 1st gen 1995–2004, TPU license plate light gasket -
Speaker coverTacoma 2001, speaker cover -
Ignition ringTacoma 1st gen and 4Runner 3rd gen, ignition ring -
Outside door handle rod clipsTacoma 1995 to 2004 and 3rd gen 4Runner, links the outside door handle to the latch rod -
Center dash storage pocketTacoma 1st gen (built for a 2004), storage pocket for the center of the dash -
Back window latchTacoma 1998, back window latch -
Wiper fluid capTacoma 2001, washer fluid cap -
Front axle seal driversTacoma 1st gen, seal drivers for the 7.5 inch front diff -
Fuel door lockTacoma 1st gen, fuel door lock -
HVAC knobTacoma 2004, HVAC knob -
Hood support rod holderTacoma 2000, hood prop rod holder -
Driver cab cornerTacoma 1997, driver side cab corner -
Dash cover1st gen Tacoma, dash cover -
Phone holder1st gen Tacoma, phone holder -
Grille clips1st gen Tacoma, OE style grille clips 90467-12040 -
Tailgate latch bushing1st gen Tacoma, tailgate latch bushing -
Single DIN radio adapter1st gen Tacoma, single DIN radio adapter -
Switch blank lighter holder1st gen Tacoma, 3rd gen 4Runner and others, switch blank Bic lighter holder -
Dome light covers1st gen Tacoma and 3rd gen Pickup, dome light covers -
Window crank washer1st gen Tacoma and similar Toyota trucks, replacement window crank escutcheon
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Toyota Tacoma 1st gen parts free?
Yes. All 66 are free to download from the creator's page. 36 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Toyota Tacoma 1st gen?
Check the years and trim in what each part fits, match the OEM part number where it's listed (1 of the 66 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Send us one
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
Got it
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.