Nissan Pathfinder parts
44 free models made for the Nissan Pathfinder, plus 13 that fit every Nissan. Looking for another Nissan? See every Nissan part.
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Nissan Pathfinder parts
44 parts-
On/off button disable bracketPathfinder 2022-2024, holds a dash on/off button in the disabled position -
Dash tray with phone holderXterra 2005–2013, Pathfinder 2005–2010 and Frontier 2005–2017 -
Wiper cowl top grilleWD21 platform Pathfinder, Hardbody and Navara cowl panels below the windshield, left and right 66820-01G00 / 66821-01G00Designed for bolts instead of clips; mirror for the other side; large print -
Wiper arm capNavara circa 2008 and possibly Pathfinder, wiper arm cap -
Rear wiper motor rack retainerNissan Pathfinder (2005), rear wiper motor piece that holds the rack on the pinion -
Radio knobPathfinder 2008–2012, volume and tuning; may fit Armada -
Rear cup holder partsFrontier, Pathfinder and Xterra -
Armrest tray2022+ Pathfinder, sits under the armrest -
Rear dash cam mount2025 Pathfinder -
Armrest trayPathfinder 2013-2020, armrest tray -
Cargo cover pinR51 Pathfinder, replaces a broken trunk cover pin -
REDARC brake controller switch blankR52 Pathfinder -
Vent handlePathfinder R51 and Navara D40 -
Cup holder phone mountD40 Navara and R51 Pathfinder 2010+ -
Rear cargo latch4th gen Pathfinder, replaces part 849B5-3JA0A -
USB passthrough2006 Pathfinder -
Trunk cover wall hookX-Trail and Pathfinder, wall hook for the trunk cover -
Dashboard phone holderPathfinder, no adhesive needed -
Dashboard phone holderNissan Pathfinder (generation not stated) -
Transmission manual release buttonPathfinder, transmission manual release button -
Foot rest plugsNavara and Pathfinder, foot rest plugs -
Park release buttonPathfinder 2009, a permanent button for the shift lock release when the brake interlock fails -
Armrest MagSafe charger trayPathfinder 2013-2020, armrest tray for a MagSafe charger -
Passenger lock actuator partNavara D40 and Pathfinder, passenger side lock actuator part -
Dashcam cable trimPathfinder, trim to hide the dashcam cable -
Hitch coverPathfinder, covers the hitch receiver -
Front cup holder insertFrontier, Pathfinder and Xterra D40 era, front cup holder insert -
Side step end capsPathfinder R51, end caps for the tubular side steps; check your tube size first -
Roof tie downsPathfinder R50 and QX4, roof tie downs -
Shifter cable bushingAutomatic shifter cable bushing: Frontier 2005-2021, Titan 2005-2021, Xterra 2005-2015, Pathfinder 2005-2012, Armada 2004-2015 34935ZR00A / 349357S00TPU only; creator calls it a temporary fix -
Hood prop rod clipFrontier 2005–2017, Pathfinder 2005–2012, Xterra 2005–2015 -
Power mirror switch blankD21 Hardbody/Navara 1988–1993, also fits Pathfinder -
Side vent trim ringD21 Hardbody/Navara 1988–1993, also fits Pathfinder, side vents with damper knob -
Fuel cap tetherPathfinder, keeps the fuel cap attached -
RJ45 pass-throughPathfinder R51 and Frontier D40, RJ45 network pass-through -
Tweeter dash adapter bracketFrontier, Xterra and Pathfinder, mounts tweeters in the dash -
Switch blankPathfinder 1996-2004, switch blank -
Hood support clipPathfinder, clip for the hood prop -
Speedometer buttonsPathfinder R51, replacement instrument cluster buttons -
Brake and cruise control stopperFrontier, Pathfinder, Xterra and other Nissans, replaces part 465845 -
Speedometer needleHardbody and Pathfinder, speedometer needle -
Outside door handleHardbody D21 and Pathfinder, outside door handle -
Hood rod holderPathfinder, clip for the hood prop rod -
Third brake light housingPathfinder 1996–2001 and Infiniti QX4 1997–2001, the bulb housing the red lens clips to 26590-0W010
Fits every Nissan
13 partsParts made for Nissan trucks in general. Check the fit on yours before you print.
-
Push pin retainerCommon Nissan/Infiniti push rivet, 8mm hole, under-hood cowl and trim panels 01553-09321 (superseded by 01553-2DR9A)Nylon preferred, PETG works; use the solid-tab retainer. 20mm and 16mm flange versions -
6.5 in speaker adapterNissan, fits 6.5 in speakers -
-
Washer fluid capNissan and Infiniti, washer fluid reservoir -
Key fob shellNissan key fob -
Reverse sensor bracketArmada 2010, replaces broken parking sensor brackets -
USB and AUX switch blankNissan switch slot, mounts GROM BT3 USB and aux ports -
Body clipsNissan bodywork, direct fit or with a wider lip -
Hood prop rod clipNissan hood support rod clip for 8mm rod; creator lists Pathfinder, Navara, D21, Sentra, Altima, Maxima, Z cars 65722-01E00 / 65722-65F00ABS, 0.16mm layers, 4 walls -
Hood prop rod clipNissan -
Hood prop rod clipNissan -
USB and aux switch blankNissan switch blank slot, mounts USB and 3.5 mm aux ports -
Magnetic phone holderNissan, uses nine 8x4 mm magnets with a slide-on cover
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Nissan Pathfinder parts free?
Yes. All 57 are free to download from the creator's page. 35 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Nissan Pathfinder?
Check the years and trim in what each part fits, match the OEM part number where it's listed (5 of the 57 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.