Lexus RX parts
30 free models made for the Lexus RX, plus 4 that fit every Lexus. Looking for another Lexus? See every Lexus part.
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Lexus RX parts
30 parts-
Key fob shellLexus RX330, key fob -
Switch blank with USB port2nd gen RX (tested 2007 RX350), dash switch blank socket; likely other Lexus/Toyota 55539-48020No supports; use a heat resistant material -
Engine cover retainer clipsRX350 engine cover; the creator says they suit Lexus and Toyota covers of the same style -
Cassette phone holderRX300, phone holder in the cassette slot for OnePlus 11 -
Center console trayLexus RX 2009 to 2015, tray for the center console -
Android phone cradleLexus RX 3rd gen, Android phone cradle -
Blank plugLexus RX, blank plug -
Headlight washer cover2016-2020 RX F Sport, left headlight washer coverPETG or ASA, not PLA; 3 perimeters, 50% infill -
Dash garnish clipRX350, dash garnish trim clip, replaces weak factory clipsASA or PA for heat, no supports -
Ignition key ring2nd gen RX, ignition cylinder trim ringPrint in white or glow material to let light through -
Backup camera mounting plate2007 RX350, replaces the factory camera bracket to hold an aftermarket camera 86790 -
Rear footwell vent extensionRX 450h, raises the rear footwell vent so the air reaches the cabin -
MagSafe wireless charger bedLexus RX 350 2016 to 2022, wireless charger bed for MagSafe phones -
Door window switch clipLexus RX300, clip for the door window rocker switch -
Backup camera adapter 86790Lexus RX350, backup camera adapter -
Roof rack slot cover2007 RX350, roof rail slot covers (front, middle and rear pieces)Tight fit; press in with a plastic trim tool -
Ashtray phone holderLexus RX300 1998–2003, phone holder in the ashtray -
Ignition ringLexus RX and Toyota Harrier, ignition key ring -
Cup holder for large cupsLexus RX350 2010 to 2015, cup holder for large cups -
A/C air deflectorLexus RX350 AL10, deflects A/C air to the front seat -
Radar detector cup holder mountRX 450h, cup holder mount for a Coyote unit -
Boot lid clipRX 400h, rear boot lid clip -
Cassette slot phone holderRX300, Xiaomi phone holder that mounts in the cassette slot -
Key fob shellRX 330, replacement key fob -
Cassette slot phone holderRX, iPhone 13 holder that mounts in the cassette slot -
Front fog light trimRX 400h, front fog light surround -
Trunk handleRX 300 first gen, trunk handle -
Fuel filler neck guardLexus RX and Toyota Highlander, fuel filler neck guard -
Rear body mount spacer bushingLexus RX and Toyota Highlander 2001 to 2013, rear body mount spacer bushing -
Armrest organizerRX350 2016–2019, center console tray
Fits every Lexus
4 partsParts made for Lexus trucks in general. Check the fit on yours before you print.
-
Floor mat clipRX400h floor mat retainer, likely many other Lexus and Toyota modelsPrint on its side with tree supports, 100% infill -
USB port switch blankLexus and Toyota, switch blank with a USB port -
Threaded oil change funnelLexus, threads into the oil filler -
Power seat drive gearToyota and Lexus power seats, 20-tooth, 23mm gear
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Lexus RX parts free?
Yes. All 34 are free to download from the creator's page. 18 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Lexus RX?
Check the years and trim in what each part fits, match the OEM part number where it's listed (2 of the 34 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.