Free Parts / Ineos / Grenadier
Ineos Grenadier parts
46 free models made for the Ineos Grenadier. Looking for another Ineos? See every Ineos part.
Add a part
Before you print
- Every model here is someone else's work. Download it from the creator's page, and give them a like while you're there.
- Licenses vary. Dashed tags are non-commercial or personal-use only: print them for your truck, don't sell them. A few are files attached to forum posts with no license stated; those link to the thread.
- Print in PETG, ASA or nylon. PLA goes soft in a cab in July. Check fitment against your old part before you print ten.
Ineos Grenadier parts
46 parts-
Cubby box insertIneos Grenadier, insert for the cubby box -
Number plate light shieldIneos Grenadier rear plate lights, cuts glare in the reverse camera; left and right versionsPETG or ABS for UV. 30% infill, no supports; tilt each side 7 degrees so it sits flat. -
Centre console storage trayIneos Grenadier, drops into the centre console as an upper storage layerPLA tested, 30% infill, 4 walls, print upright with supports on the tabs. Needs a 190 x 160 mm bed. -
Central display screen shadeIneos Grenadier, shades the center touchscreen from glare -
Cup holder enlargerIneos Grenadier front cup holder, sized so a Yeti mug fits -
Low-profile sunglasses holderGrenadier, bolts to the overhead console -
12V socket and RAM mountGrenadier, attaches to the lower front console -
Barrier and hanger hole plugIneos Grenadier 13 mm barrier mounting holes; takes an M6 bolt to hang gearPLA Pro, 0.16 mm layers, 50% infill, 4 walls, with support. -
Phone and cup holderGrenadier, mounts on top of the center console -
Phone holderGrenadier, bolts to the console panel; made for an iPhone 14 Pro -
Overhead shelfGrenadier, overhead shelf with glasses holder -
Wolfbox mirror dash cam bracketGrenadier MY23–MY24 without ADAS, replaces the original rear-view mirror -
Phone mountIneos Grenadier, holds a phone in the cab -
Overhead glasses case, tallGrenadier, mounts to the unused overhead console panel -
Gridfinity centre console insertIneos Grenadier and Quartermaster centre console; magnetic and non-magnetic versionsPETG for cabin heat, supports on build plate only. -
Roof power outlet coverIneos Grenadier, replacement cover for the factory roof power outletsPrinted in CF nylon for weather; ASA also works. -
Microphone bracket and bag hookGrenadier dash, suits the GME UHF magnetic mic mount -
Throttle pedal extensionGrenadier, raises the pedal 22 mm, helps in RHD vehicles -
Spotlight blanking coverIneos Grenadier front factory spotlights, hides them when bigger driving lights are fittedPETG or ABS, 50% infill or more, outside face down. Fit with a bead of silicone so it can come off. -
Trailer wiring plate adapterIneos Grenadier; mounts a 7-pin trailer plug to the rear bumper using factory holes -
Cable tie-downsGrenadier, keeps cables out of the shifter and dash area -
Rear under-seat storage boxGrenadier, under the rear seat -
JBL Nano Pro underseat mountGrenadier, screwless mount under the driver's seat -
Rear vent protectorGrenadier rear vents -
ADAS fault light maskGrenadier, hides the ADAS warning lights -
Tie-down ring storage railGrenadier, holds up to 12 L-track tie-down rings on the utility belt -
Steel wheel nut coverIneos Grenadier stock steel wheels; short sleeve for use with a nut check, tall withoutASA for exterior use, standard ASA settings. -
Sunglasses holderGrenadier -
UHF mic mountGrenadier and Quartermaster, uses existing holes on the upper row of dials -
-
Front vent block-off platesGrenadier, block-off plates for the front vents -
Passenger floor mat pinGrenadier, retaining pin for the passenger floor mat -
Backup camera extension armGrenadier, moves the camera 20 cm left and 13 cm back -
Roof rack end capsIneos Grenadier (2022+) -
L-track connectorIneos Grenadier, attaches small accessories to the L-track -
MagSafe phone mountGrenadier, MagSafe phone mount -
Rear seat cup holderIneos Grenadier rear footwell between the seats; two cups plus storage, 11 in wideRotate in the slicer so it sits flat. -
Coat hangerIneos Grenadier, screw-on hanger plate for the dog and luggage guard mounting points -
Large cup holder and phone holderIneos Grenadier and Quartermaster, oversized cup holder with phone holder -
Phone mount for 16 to 17mm ball chargersIneos Grenadier, holds a ball-mount phone charger -
Rear door hold-open sleeveIneos Grenadier, locks the rear door in the open position -
Sun visor extensionIneos Grenadier, slide-out visor extensions that add up to 15 cm of side shade; the passenger side takes a 4 x 6 in mirrorNeeds a large bed, a Prusa XL or similar. -
SP Connect phone mountGrenadier, phone mount for SP Connect -
Under seat safe coverIneos Grenadier, facade that hides the aftermarket under seat safe once it has a keyed lock -
Door top tweeter mountIneos Grenadier, mounts speaker tweeters in the top of the door -
Roof power outlet coverIneos Grenadier, cover and casing for the roof power outlet
Any make
2 partsParts that fit more than one make. Measure before you print.
-
Grille clipIsuzu, Toyota, Mazda and Mitsubishi grilles Isuzu 8942180270 · Toyota 90467-13011 -
Push-in rivet clip, 6 to 10 mmAny make. Measure the hole and the panel
Nothing for this model yet. Send us one.
Questions
Are these Ineos Grenadier parts free?
Yes. All 46 are free to download from the creator's page. 36 of them are personal or non-commercial use only, so print them for your own rig and don't sell them. The license is on every row.
How do I find the right part for my Ineos Grenadier?
Check the years and trim in what each part fits, match the OEM part number where it's listed (0 of the 46 have one), or compare the old part with the preview photos.
What filament should I print these in?
PETG, ASA or nylon for anything in the cab or under the hood. PLA goes soft in a hot cab, so save it for a test fit. Print one, check the fit, then print the rest.
Where do the files come from?
Thingiverse, Printables, MakerWorld, Cults3D, Thangs, Creality Cloud, MyMiniFactory and owner forums. LRDT doesn't host the files; every part links to its creator's page.
Send us one
Know a part we're missing?
Drew one yourself, or found one that saved your weekend? Send the link. We check the fit and the license, then add it here with the creator's name on it. FJ Cruiser trim clips, JL and Gladiator hardtop clips, 2nd-gen Trooper push clips and Patrol clips are the gaps we'd most like to fill.
Got it
We'll check the fit and the license, and if it's good it goes up with the creator's name on it.